Quick picks
DeWalt DW890
Consider for: A supported cut path requiring the documented swiveling head
Main limitation: No FindItWise application, finish-quality or handling test
View on Amazon.com (opens in a new tab)View on Amazon.ca (opens in a new tab)Read product details ↓Makita JS1602
Consider for: A supported thinner-sheet cut requiring the documented smaller radius
Main limitation: No FindItWise application, finish-quality or handling test
View on Amazon.com (opens in a new tab)View on Amazon.ca (opens in a new tab)Read product details ↓Makita JS3201
Consider for: A supported heavier-sheet cut within the exact material ratings
Main limitation: No FindItWise application, finish-quality or handling test
View on Amazon.com (opens in a new tab)View on Amazon.ca (opens in a new tab)Read product details ↓Compare the documented specifications
| What matters | DeWalt DW890 | Makita JS1602 | Makita JS3201 |
|---|---|---|---|
| Best for | A supported cut path requiring the documented swiveling head | A supported thinner-sheet cut requiring the documented smaller radius | A supported heavier-sheet cut within the exact material ratings |
| Head | 360-degree swivel | Not verified | Not verified |
| Minimum cutting radius | 5-1/2 inches | Not verified | Not verified |
| Removed strip | 7/32 inch | Not verified | Not verified |
| Mild steel capacity | Not verified | 16 gauge | 10 gauge |
| Stainless steel capacity | Not verified | 18 gauge | 13 gauge |
| Cutting radius | Not verified | 1-3/16 inches | 2 inches |
| Amazon | View on Amazon.com (opens in a new tab)View on Amazon.ca (opens in a new tab) | View on Amazon.com (opens in a new tab)View on Amazon.ca (opens in a new tab) | View on Amazon.com (opens in a new tab)View on Amazon.ca (opens in a new tab) |
Specify the sheet and the cut path first
An electric metal shear should be selected against the material, thickness and required path through the sheet. A tool’s broad gauge label is an incomplete comparison when it omits the material or the radius needed around a corner. DeWalt DW890, Makita JS1602 and Makita JS3201 provide three documented configurations to investigate.
Our portable band-saw guide covers a different metal-cutting arrangement. Use this guide when the supported operation specifically calls for sheet-metal shearing, rather than assuming one tool category covers every metal workpiece.
DW890: swiveling head and a removed strip
The DW890 manufacturer record documents a head that swivels through 360 degrees. It describes a removed strip 7/32 inch wide that curls out of the cutting area, and specifies cuts with a radius of 5-1/2 inches or larger.
Investigate this arrangement when that cut path and head adjustment suit the work. Plan the removed strip and required clearance instead of assuming a cut preserves all material. The available sheet around the intended line belongs in the purchase notes alongside the required curve.
JS1602: separate mild-steel and stainless ratings
The JS1602 specification table lists 16-gauge mild-steel capacity and 18-gauge stainless capacity, with a 1-3/16-inch cutting radius. It records no 360-degree rotating head.
This is a candidate when the exact material and intended curve fit those documented limits. Keep the two material rows separate: the mild-steel figure is not a stainless-steel allowance. Gauge should remain attached to its material description rather than being converted casually into a universal thickness claim.
JS3201: different capacities and a two-inch radius
The JS3201 record lists 10-gauge mild-steel and 13-gauge stainless capacities with a two-inch cutting radius. It identifies the supplied shear blade set and thickness gauge.
Investigate it when those heavier-sheet ratings and path requirements are actually needed. Do not rank it above JS1602 merely because the mild-steel capacity differs. The required curve, supported operation and complete setup can rule out a tool even when one headline capacity seems sufficient.
Compare complete working requirements
Record the exact material, required path, minimum radius and necessary edge clearance beside each shortlisted model. Then check the applicable instructions and replacement cutting components. A shared brand or a familiar gauge label does not establish interchangeable blades.
The reciprocating-saw specifications guide discusses another cutting system and shows why a stroke-rate label alone does not establish working results. Its blade reach values do not transfer to these shears. Here, capacity and path requirements are the supported first filters.
Verify the offer without inventing a performance winner
All three exact model titles and selected ASINs were independently verified in US and Canadian Amazon listings. A separate nibbler candidate had conflicting voltage information and was excluded; it is not treated as an interchangeable alternative to the selected shear.
Confirm the current seller package, required power supply and cutting components before ordering. Listing identity does not establish stock, delivery or seller authenticity. FindItWise has not measured cutting effort, edge distortion, achieved radius or durability with these tools.
DeWalt · Model DW890
View on Amazon.com (opens in a new tab)View on Amazon.ca (opens in a new tab)Confirm the seller’s included items before purchasing.
DeWalt DW890
Corded swivel-head sheet-metal shear.
| Head | 360-degree swivel |
|---|---|
| Minimum cutting radius | 5-1/2 inches |
| Removed strip | 7/32 inch |
Reasons to consider
- Manufacturer identifies the exact configuration
Trade-offs
- No FindItWise application, finish-quality or handling test
Specifications: swivel-head-shear-18-gauge manufacturer documentationJS1602 manufacturer documentationJS3201 manufacturer documentation · Checked 2026-11-13
Makita · Model JS1602
View on Amazon.com (opens in a new tab)View on Amazon.ca (opens in a new tab)Confirm the seller’s included items before purchasing.
Makita JS1602
Corded shear with documented material-specific capacities.
| Mild steel capacity | 16 gauge |
|---|---|
| Stainless steel capacity | 18 gauge |
| Cutting radius | 1-3/16 inches |
Reasons to consider
- Manufacturer identifies the exact configuration
Trade-offs
- No FindItWise application, finish-quality or handling test
Specifications: swivel-head-shear-18-gauge manufacturer documentationJS1602 manufacturer documentationJS3201 manufacturer documentation · Checked 2026-11-13
Makita · Model JS3201
View on Amazon.com (opens in a new tab)View on Amazon.ca (opens in a new tab)Confirm the seller’s included items before purchasing.
Makita JS3201
Corded ten-gauge shear with a documented blade set.
| Mild steel capacity | 10 gauge |
|---|---|
| Stainless steel capacity | 13 gauge |
| Cutting radius | 2 inches |
Reasons to consider
- Manufacturer identifies the exact configuration
Trade-offs
- No FindItWise application, finish-quality or handling test
Specifications: swivel-head-shear-18-gauge manufacturer documentationJS1602 manufacturer documentationJS3201 manufacturer documentation · Checked 2026-11-13
Sources & references
- swivel-head-shear-18-gauge manufacturer documentation — accessed November 13, 2026
- JS1602 manufacturer documentation — accessed November 13, 2026
- JS3201 manufacturer documentation — accessed November 13, 2026